imfdb.org  

Go Back   imfdb.org > The Forum > Just Guns

Reply
 
Thread Tools Display Modes
  #21  
Old 08-07-2015, 03:34 AM
Jcordell Jcordell is offline
Formerly "Checkman"
IMFDB Admin
 
Join Date: Nov 2008
Location: Idaho
Posts: 1,034
Default

Quote:
Originally Posted by Mazryonh View Post
Well, that just gives more reason for those using purpose-built .40 S&Ws to go and try 10mm handguns. Conversion barrels to .40 S&W are usually available for those.
I always heard good things about the S&W 1006. Built like a boat anchor. Not meant to be a CCW pistol, but very solid. I own a second generation S&W Model 745 and that's one solid pistol. Again pretty massive, but I didn't buy it to carry on my ankle.
Reply With Quote
  #22  
Old 08-07-2015, 05:23 AM
AdAstra2009's Avatar
AdAstra2009 AdAstra2009 is offline
Senior Member
 
Join Date: Nov 2008
Location: Maryland
Posts: 1,067
Default

Quote:
Originally Posted by Jcordell View Post
I always heard good things about the S&W 1006. Built like a boat anchor. Not meant to be a CCW pistol, but very solid. I own a second generation S&W Model 745 and that's one solid pistol. Again pretty massive, but I didn't buy it to carry on my ankle.
OMG I want a S&W 1006/1076, looks just like the 4506 but in the bear killing 10mm, not the obsolete .45 ACP!!!
Reply With Quote
  #23  
Old 08-07-2015, 05:51 AM
Mazryonh Mazryonh is offline
Senior Member
 
Join Date: Feb 2010
Posts: 290
Default

Quote:
Originally Posted by Jcordell View Post
I always heard good things about the S&W 1006. Built like a boat anchor. Not meant to be a CCW pistol, but very solid. I own a second generation S&W Model 745 and that's one solid pistol. Again pretty massive, but I didn't buy it to carry on my ankle.
You could probably carry a Glock 29 on your ankle. But that would be pretty hard to handle in a live-fire situation without lots of practice.

Quote:
Originally Posted by AdAstra2009 View Post
OMG I want a S&W 1006/1076, looks just like the 4506 but in the bear killing 10mm, not the obsolete .45 ACP!!!
S&W is largely out of the business of making handguns in that caliber. You might want to try the newer SIG P220 in 10mm instead.
Reply With Quote
  #24  
Old 08-07-2015, 10:25 PM
AdAstra2009's Avatar
AdAstra2009 AdAstra2009 is offline
Senior Member
 
Join Date: Nov 2008
Location: Maryland
Posts: 1,067
Default

The SIG P220 in 10mm for $1400, no thank you. The S&W 10mms are usually in the 7-900 dollar range and the Glock 20/29 isn't meant to fire the full power 10mms unless you fork out the money for an aftermarket barrel with a fully supported chamber. the S&W 1006/1076/1066 are one of the few 10mm pistols from what I understand can run full power loads in their factory configuration.
Reply With Quote
  #25  
Old 08-08-2015, 05:19 AM
Excalibur's Avatar
Excalibur Excalibur is offline
IMFDB Admin
 
Join Date: Nov 2008
Location: USA
Posts: 3,842
Send a message via AIM to Excalibur Send a message via MSN to Excalibur Send a message via Yahoo to Excalibur
Default

Actually all you need for the 10mm Glock to shoot better is a stronger guide rod and that's it. A buddy of mine has one as his carry gun
__________________

"There's a fine line between not listening and not caring...I like to think I walk that line everyday of my life."

Blessed be the LORD, my rock, Who trains my hands for war, And my fingers for battle
Psalm 144:1

“It is always wrong to use force, unless it is more wrong not to.”
Reply With Quote
  #26  
Old 08-08-2015, 05:40 AM
Mazryonh Mazryonh is offline
Senior Member
 
Join Date: Feb 2010
Posts: 290
Default

Quote:
Originally Posted by AdAstra2009 View Post
The SIG P220 in 10mm for $1400, no thank you.
A Glock's price point that ain't. You could go get a Rock Island Armoury in M1911 in 10mm instead.

Quote:
Originally Posted by AdAstra2009 View Post
The S&W 10mms are usually in the 7-900 dollar range and the Glock 20/29 isn't meant to fire the full power 10mms unless you fork out the money for an aftermarket barrel with a fully supported chamber. the S&W 1006/1076/1066 are one of the few 10mm pistols from what I understand can run full power loads in their factory configuration.
The 10mm Glocks can fire full-power 10mm loads with their stock barrels, it's just that the brass ejected will be bulged, which means it can't be reused for handloading (though of course it can still be melted back down to be recycled). The unsupported part of the chamber in stock Glock barrels is to increase feeding reliability, but this obviously has its drawbacks with regards to higher-pressure cartridges. Given the ubiquity of Glocks, however, finding conversion barrels at reasonable prices shouldn't be too difficult. The S&W 1006 series is also made on single-stack frames, and that means you get stock with single-stack magazine capacities which you can't increase by much afterwards.

Last edited by Mazryonh; 08-09-2015 at 03:50 AM.
Reply With Quote
  #27  
Old 08-09-2015, 06:37 AM
S&Wshooter's Avatar
S&Wshooter S&Wshooter is offline
Senior Member
 
Join Date: Dec 2009
Location: Texas
Posts: 4,936
Default

Quote:
Originally Posted by AdAstra2009 View Post
OMG I want a S&W 1006/1076, looks just like the 4506 but in the bear killing 10mm, not the obsolete .45 ACP!!!
.45 Super, man. If I had a spare 4506, I'd look into it

I don't really have a need for 10mm; reckon having a .45 that'll eat +P+ indefinitely will do whatever I'd need a 10mm for
__________________
Get off of my property


http://www.introvertisland.com
Reply With Quote
  #28  
Old 08-13-2015, 01:49 AM
AdAstra2009's Avatar
AdAstra2009 AdAstra2009 is offline
Senior Member
 
Join Date: Nov 2008
Location: Maryland
Posts: 1,067
Default

Quote:
Originally Posted by S&Wshooter View Post
.45 Super, man. If I had a spare 4506, I'd look into it

I don't really have a need for 10mm; reckon having a .45 that'll eat +P+ indefinitely will do whatever I'd need a 10mm for
Is that something that I'd need to have the gunsmith do? Also I have the 4506-0
Reply With Quote
  #29  
Old 08-13-2015, 11:49 AM
commando552 commando552 is offline
IMFDB Admin
 
Join Date: Jan 2012
Location: England
Posts: 547
Default

Quote:
Originally Posted by AdAstra2009 View Post
Is that something that I'd need to have the gunsmith do? Also I have the 4506-0
The two rounds are externally exactly the same size, I imagine the only difference that you would need would be a stiffer recoil spring. There are also a few other parts that I imagine it would be a good idea to upgrade, but I think the recoil spring would be the only thing that you would really have to change. Thinking about it, I imagine that a spring meant for a 1006 would probably do.
Reply With Quote
  #30  
Old 08-13-2015, 05:28 PM
AdAstra2009's Avatar
AdAstra2009 AdAstra2009 is offline
Senior Member
 
Join Date: Nov 2008
Location: Maryland
Posts: 1,067
Default

Quote:
Originally Posted by commando552 View Post
The two rounds are externally exactly the same size, I imagine the only difference that you would need would be a stiffer recoil spring. There are also a few other parts that I imagine it would be a good idea to upgrade, but I think the recoil spring would be the only thing that you would really have to change. Thinking about it, I imagine that a spring meant for a 1006 would probably do.
I've done a little bit of reading and a lot of people recommend some kind of upgrade kit specifically talking about a recoil buffer or something like that, something along the lines of it being needed or .45 super will wear the gun out faster -and being that the 4506 is no longer supported by S&W that would suck
Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 11:26 PM.


Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.