Cylinder not closing on my revovler.....
 

Keeps coming out, seems the cylinder release is very stiff and wont go into the closed position, just stays forward. Even holding it back i can only get the cylinder to stayt sometimes, then its a chore rleasing it again. weird.

What mode of revolver is it?

taurus 669

Is it a brand new revolver? If it is you can send it back to Taurus. Even if it isn't new they still may be able to fix it for you.

They got a lifetime warranty, but legendarily bad service, its a 1988 made model. i was hoping there may be an easy diy fix to avoid the shipping fees, the hassle, and the not having a working handgun.

I believe they pay for the shipping. Don't you have other handguns?

in 21 days i'll have other handguns :)

Seems it is a cylinder release issue. Wonder if it's easy to fix.

Are there any local smiths you can take it to? Detail stripping one of them (a revolver) is much more complex than an auto.

Or you can always buy one of the AIG videos and see if you want to tackle it yourself.

I had the same problem with a Taurus .22 my family bought. But the problem was fixed by Taurus for free.

Not exactly. Something S&W based will be relatively easy, not requiring any punches for pins, just screwdrivers to get the sideplate off.

I have some advice as I've opened up my 19 before, but do this at your own risk. Also I'm assuming this gun is built very similarly to a Smith

First off, you can simply unscrew the release latch and see if that helps at all. It'll partially expose the actual release part (I'm not sure of its technical name) which actually depresses the cylinder plunger and unlocks the cylinder.

If that doesn't work, you'll have to take the sideplate off the gun and look inside. Taurus guns are very similar to S&W guns, and being this is an older one I'm assuming it' will be even more similar than say a newer one, but, I reiterate, do this at your own risk. You may just end up with a buncha parts out and you might have no clue how to get them back in. I would find a cutaway or schematic of a Taurus 669 or something similar before doing anything inside the gun or take detailed pictures of it with the parts still in so as to have a frame of reference.

Get out what needs to come out to get to the release part and examine it. In all likelihood it's just filled with carbon or grit from lots of firing, lack of maintenance, or both, or perhaps a spring that's part of the mechanism is caught. The mechanism itself might just need to be taken apart and rebuilt as well, but at the very worst the part is broken and will have to be replaced.

And, as someone else has said, if you aren't daring enough (don't kick yourself for that, I've gotten in too deep myself a couple of times) just take it to a gunsmith and have them take a look, granted they don't charge you too much money.

im calling a local smith seeing if they can take a look and see if its a quick fix or send it back. Its my first handgun so i kinda want to hold on to it.

Also, from experience dismantling my Airsoft revolver, do it in a room where there are no places a flying spring could be eaten by the Carpet Monster. Not sure how it is for real handguns (banned over here), but I think all Airsofts must be required by law to contain a V-shaped spring which refuses to fit into the frame at any angle and is set to fire itself three feet from your workbench the second the sideplate comes off.

To my knowledge there are no springs that will fly out of the gun, they should all be contained. The hammer block may come loose but that isn't spring loaded and is easily placed back in. Again, though, this is based on my opening of a S&W K-Frame revolver.

Usually a cylinder latch problem is the result of a faulty latch spring. It's a tiny little spring installed under the latch (it's what makes the latch move back and forth, but that's pretty obvious).

Like YNH said, it's at your own risk whenever you take a six-gun apart. Sometimes putting them back together is near impossible without visual instruction or a smith's assistance. Also, depending on if the latch spring needs to be replaced or not, some revolvers have a simple spring that's easily replaceable while others have this weird flattened spring that's a pain and a half to aquire (or at least aquire cheaply). I'm pretty sure that those are only in large frame Colt revolvers though (from my experience at least) so hopefully you won't run into one.

If you're bringing it to a gunsmith though, they should be able to fix it fine. Just hope you don't need a flat spring replaced. That will be an extra hassle you don't want.

Yeah, but from experience it's always a good idea to assume anything mechanical you take apart will have a tiny springy thingy that will fly under the hardest thing in the room to move and take precautions to that effect. If you don't, it always will. :mad:

Airsoft guns are put together in a way that makes disassembly/reassembly very difficult. All the parts kind of hold together at once, and if you don't have 7 hands or a machine to hold those parts, you've likely ruined the gun by taking it apart.

Real guns are designed to be stripped when needed, airsoft guns... I don't know what they were thinking with most of them.